- Bạn vui lòng tham khảo Thỏa Thuận Sử Dụng của Thư Viện Số
Tài liệu Thư viện số
Danh mục TaiLieu.VN
Giáo trình Kỹ thuật rèn và dập nóng: Phần 2
Nối tiếp nội dung phần 1, phần 2 cuốn giáo trình "Kỹ thuật rèn và dập nóng" cung cấp cho người đọc các kiến thức: Quy trình công nghệ rèn tự do; rèn thép dụng cụ, thép hợp kim cao và kim loại màu; nhiệt luyện và kiểm tra vật liệu, công nghệ dập nóng, máy ép trục khuỷu dập nóng, máy ép ma sát trục vít, máy cắt vành biên, tổ chức sản xuất, an...
127 p utehy 25/09/2023 74 0
Từ khóa: Giáo trình Kỹ thuật rèn, Kỹ thuật rèn, Kỹ thuật dập nóng, Tổ chức sản xuất, An toàn lao động, Máy cắt vành biên, Công nghệ rèn tự do, Rèn thép dụng cụ
Ebook Sổ tay dụng cụ cắt và dụng cụ phụ: Phần 1
Ebook Sổ tay dụng cụ cắt và dụng cụ phụ: Phần 1 trình bày các nội dung chính sau: Vật liệu để chế tạo dụng cụ cắt; Thép dụng cụ; Hợp kim cứng; Vật liệu mài; Các loại dụng cụ cắt; Phần nối ghép của dụng cụ cắt với dụng cụ phụ;... Mời các bạn cùng tham khảo để nắm nội dung chi tiết.
222 p utehy 31/01/2023 55 2
Từ khóa: Dụng cụ cắt, Chế tạo dụng cụ cắt, Thép hợp kim, Hợp kim cứng, Vật liệu mài, Dụng cụ cắt ren, Đá mài kim cương
Bài giảng Thiết kế dụng cụ cắt: Chương 5 - PGS.TS. Bùi Ngọc Tuyên
Bài giảng Thiết kế dụng cụ cắt: Chương 5 - Thiết kế dụng cụ cắt ren được biên soạn bởi PGS.TS. Bùi Ngọc Tuyên có nội dung chính trình bày về: Khái niệm, công dụng, phân loại của ren; Thông số cơ bản của ren; Các phương pháp gia công ren; Thiết kế dao tiện ren; Ta rô và bàn ren;... Mời các bạn cùng tham khảo bài giảng dưới đây để nắm được...
8 p utehy 31/01/2023 28 1
Từ khóa: Bài giảng Thiết kế dụng cụ cắt, Thiết kế dụng cụ cắt, Thiết kế dụng cụ cắt ren, Thông số cơ bản của ren, Các phương pháp gia công ren, Thiết kế dao tiện ren, Ta rô và bàn ren
Bài giảng Lắp đặt hệ thống tự động hóa 1: Bài 1 - ThS. Nguyễn Thị Lan
Bài giảng Lắp đặt hệ thống tự động hóa 1: Bài 1 Các công cụ dụng cụ cầm tay được biên soạn với mục tiêu nhằm giúp sinh viên xác định được và mô tả được các loại công cụ, dụng cụ bằng tay và bằng điện sử dụng trong lĩnh vực đo lường tự động hóa. Mời các bạn cùng tham khảo!
62 p utehy 28/12/2022 70 2
Từ khóa: Bài giảng Lắp đặt hệ thống tự động hóa, Lắp đặt hệ thống tự động hóa, Tự động hóa, Dụng cụ tạo ren trong, Quy trình tạo một ren lỗ, Dụng cụ cắt ống luồn dây
Đăng nhập
Bộ sưu tập nổi bật
8 1769
20 4421
16 3149
10 2219
Bộ sưu tập Công nghệ thông tin
12 2514
16 3623
Bộ sưu tập Quản trị kinh doanh
14 2801
14 3309